Front Rear Wheels

1965-82 Corvette Deluxe Brake Caliper O-Ring Kit 4Wheel

1965-82 Corvette Deluxe Brake Caliper O-Ring Kit 4Wheel
1965-82 Corvette Deluxe Brake Caliper O-Ring Kit 4Wheel
1965-82 Corvette Deluxe Brake Caliper O-Ring Kit 4Wheel
1965-82 Corvette Deluxe Brake Caliper O-Ring Kit 4Wheel

1965-82 Corvette Deluxe Brake Caliper O-Ring Kit 4Wheel

1965-82 Corvette Deluxe Brake Caliper O-Ring Kit 4Wheel. O-Ring Brake Caliper Conversion Kit. Everything you need to completely Rebuild and Upgrade all 4 of your leaky brake calipers to the trouble free O-Ring Piston design.

O-Ring Brake Caliper O-Ring Conversion Kit. Everything you need to completely Rebuild and Upgrade your leaky brake calipers to the trouble free O-Ring Piston design. Vette Corvette Brake Caliper Conversion Kits allow you to not only completely rebuild, but upgrade your existing brake calipers quickly, easily and affordably.

With all the savings and upgrades these kits are truly a no brainer. Upgrade today to the trouble free O-ring Piston design that also gives you double the sealing power, virtually eliminating the common problematic leaking caliper syndrome. Lip seal design seals are used on 1965 -1982 Corvette calipers. Lip seals have inherent problems.

GM quit using lip seal calipers because of problems in 1982. When they sit for a period of time they leak brake fluid.

When they are used on a Corvette with warped or out of spec rotors and or spindles, loose bearings or a Corvette that is driven hard; they can actually suck air into the caliper fluid area causing a loss of brake pedal. This is called reverse air oscillation. O-Ring seals virtually eliminate all of these lip seal problems. If GM doesn't use lip seal calipers anymore why are you? Upgrade & Rebuild at the Same Time.

Kit does 1 Car Set of Corvette Calipers. 16 O-Ring Pistons 16 Piston O-Rings 16 Pistons Dust Boots 16 Stainless Steel Springs 6 Caliper Half O-Rings 2 Copper Brake Hose Washers. 4 Pad Pins with Cotter Pins 4 Inlet Plugs 4 Plastic Caliper Bags 4 Styrofoam Placement Holding Blocks. 9 out of 10 of all Corvette brake calipers are already sleeved and ready for our conversion kits? This makes rebuilding and converting to the desired O-Ring piston design easy, quick and affordable.

Simply disassemble your old existing calipers, clean, paint and install one of our Conversion kits and you're all done! Please check to make sure your your calipers are stainless steel sleeved before ordering. This kit was engineered for "Second Design" Corvette Brake Calipers which were on all Corvettes from 1967-82.

1965 and 1966 Corvettes had "1st Design" Calipers and are identifiable by the short 3/8 Diameter center post coming from the bottom of the Aluminum Caliper pistons on both Front and Rear Brake Calipers. The casting also has 2 pieces shaped like this; coming up from the bottom of each bore and act as a guide for the post on the piston. 99.9% of the time 1st Design calipers are modified to 2nd Design when the caliper are rebuilt and or Sleeved. Check your castings before you make your order!

If you feel that your experience with us was anything less than 5 stars please let us know. Please choose carefully when time is an issue. By purchasing you agree to all of the following.

In the rare event of any further delays or backorders we will notify you with the option for a "no questions asked order cancellation". Please select your carrier wisely, lower prices do not always guarantee "Good Service".

For an estimate of these charges, we suggest you contact your local parcel carrier office or local government. We will not mark any items as gift or sample. Make a wise choice before opening.

If any item is installed or removed it is not returnable; would you want us to send you something somebody else already opened or installed? If we see any concerns with your order we will notify you. If we do not receive any replies within 5 days we reserve the right to cancel your order. Like a regular paper check, an eCheck may take 3-5 work days to clear.

The time it takes to clear is more time added to process your order. Feedback is important to us as we know it is to you. The item "1965-82 Corvette Deluxe Brake Caliper O-Ring Kit 4Wheel" is in sale since Friday, August 13, 2010. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Brakes & Brake Parts\Discs, Rotors & Hardware".

The seller is "cssbinc" and is located in Miami, Florida. This item can be shipped worldwide.

  • Manufacturer Part Number: CSSB
  • Placement on Vehicle: Left
  • Brand: HT-KITALL4
  • Warranty: Yes


1965-82 Corvette Deluxe Brake Caliper O-Ring Kit 4Wheel